[1]李　光.X100钢级管线钢焊接接头热影响区粗晶区冷却时间计算方法研究[J].焊管,2022,45(1):1-4.[doi:10.19291/j.cnki.1001-3938.2022.01.001]
　LI Guang.Cooling Time Calculation Method Research of Coarse-grained Heat Affected Zone for X100 Pipeline Steel Welded Joint[J].,2022,45(1):1-4.[doi:10.19291/j.cnki.1001-3938.2022.01.001]
点击复制

X100钢级管线钢焊接接头热影响区粗晶区冷却时间计算方法研究()
分享到：

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
45
期数:
2022年第1期
页码:
1-4
栏目:
试验与研究
出版日期:
2022-01-28

文章信息/Info

Title:
Cooling Time Calculation Method Research of Coarse-grained Heat Affected Zone for X100 Pipeline Steel Welded Joint
文章编号:
10.19291/j.cnki.1001-3938.2022.01.001
作者:
李　光
西安石油大学 材料科学与工程学院，西安 710065
Author(s):
LI Guang
School of Materials Science and Engineering, Xi’an Shiyou University, Xi’an 710065, China
关键词:
X100钢级管线钢; 热影响区粗晶区; 理论经验公式; 最小二乘法拟合; 拉格朗日插值
Keywords:
X100 pipeline steel;  CGHAZ;  theoretical empirical formula;  least squares fitting;  Lagrange interpolation
分类号:
TG402
DOI:
10.19291/j.cnki.1001-3938.2022.01.001
文献标志码:
A
摘要:
为了研究冷却时间t8/5对X100钢级管线钢焊接接头粗晶区组织性能的影响，采用单丝埋弧焊堆焊X100钢级管线钢板，利用热电偶和函数记录仪等设备测量了粗晶区的冷却时间t8/5，分别采用最小二乘法拟合与拉格朗日插值得到t8/5的计算公式，并对理论经验公式、最小二乘法拟合公式与拉格朗日插值公式计算结果进行了试验验证。验证结果表明，最小二乘法拟合公式的计算结果和测量值最接近，可以用来计算X100钢级管线钢热影响区粗晶区的冷却时间t8/5，也为合理制定X100钢级管线钢的焊接工艺提供了重要依据。
Abstract:
In order to study the effect of cooling time t8/5 on the microstructure and properties of coarse grain zone of X100 pipeline steel welded joint, single wire submerged arc welding surfacing X100 pipeline steel plate was used. The cooling time t8/5 of coarse grain zone was measured by thermocouple and function recorder. The calculation formula of t8/5 was obtained by least squares fitting and lagrange interpolation respectively. The calculation results of least squares fitting formula and Lagrange interpolation formula are verified by the experiments.The verification results show that the calculation results of the least square fitting formula of are closest to the measured values, which can be used to calculate the cooling time t8/5 of the coarse grain zone in the heat affected zone of X100 pipeline steel, and also provide an important basis for reasonably formulating the welding process of X100 pipeline steel.

参考文献/References:

[1] 曹强，李亮，陈熙，等. X100管线钢的焊接工艺评定[J]. 焊接技术，2020，49（12）:50-51.[2] 张清清，章传国，郑磊. t8/5时间对X80管线钢热影响区组织和韧性的影响[J]. 中国冶金，2017，27（12）:26-31.[3] RONEVICH J A，D’ELIA C R，HILL M R. Fatigue crack growth rates of X100 steel welds in high pressure hydrogen gas consi-dering residual stress effects[J]. Engineering Fracture Mechanics，2018（194）:42-51.[4] ZHAO J，XIONG D，GU Y H，et al.A comparative study on the corrosion behaviors of X100 steel in simulated oilfield brinesunder the static and dynamic conditions[J]. Journal of Petroleum Science and Engineering，2019（173）:1109-1120.[5] 李光. X100管线钢焊接热影响区的组织性能研究[D]. 西安: 西安石油大学，2014:13-14.[6] 许波，周建平，许燕，等. 壁厚对X80管线钢焊接热循环参数的影响[J]. 新疆大学学报（自然科学版），2020，37（2）:248-254.[7] WANG X N，ZHAO Y J，GUO P F，et al. Effect of heat input on M-A constituent and toughness of coarse grain heat-affected zone in an X100 pipeline steel[J]. Journal of Materials Engineering and Performance，2019（28）:1810-1821.[8] WANG H B，WANG F L，SHI G H，et al. Effect of welding heat input on microstructure and impact toughness in CGHAZ of X100Q steel[J]. Journal of Iron and Steel Research International，2019，26（6）:637-646.[9] WANG X L，MA X P，WANG Z Q，et al. Carbon microalloying effect of base material on variant selection in coarse grained heat affected zone of X80 pipeline steel[J]. Materials Characterization，2019（149）:26-33.[10] 迟艳芬，刘照元，王振刚，等. X70管线钢厚板多层多道焊残余应力数值分析[J]. 焊接，2020（8）:9-15，61.[11] 严春妍，元媛，张可召，等. X100管线钢焊接冷裂纹敏感性[J]. 焊接学报，2019，40（12）:41-46.[12] 张文钺. 焊接冶金学[M]. 北京: 机械工业出版社，2011:167-169. [13] SHIN S Y，OH K，KANG K B. Improvement of charpy impact properties in heat affected zones of API X80 pipeline steels containing complex oxides[J]. Materials Science and Technology，2010（26）：1049-1058.[14] 张河健，李烈军，高吉祥，等. 深海用X70管线钢焊接粗晶热影响区组织和性能研究[J]. 热加工工艺，2017，46（1）:57-60.[15] 张灵芝，李光，徐学利，等. X80管线钢单丝埋弧焊接热循环的测定[J]. 电焊机，2014，44（8）:128-130. [16] 王正林，龚纯，何倩. 精通MATLAB科学计算[M]. 北京：电子工业出版社，2007：73-74.

备注/Memo

备注/Memo:
收稿日期：2021-09-26作者简介：李 光（1988—），男，硕士，工程师，主要从事材料成型工艺方面的研究工作。
更新日期/Last Update: 2022-02-10