[1]徐 刚,杨 东,廖广平,等.基于上下位机的中频弯管机控制系统[J].焊管,2008,31(3):58-60.[doi:1001-3938(2008)03-0058-03]
 XU Gang,YANG Dong,LIAO Guang-ping,et al.Medium-frequency Bending Pipe System Based on up and down Computer[J].,2008,31(3):58-60.[doi:1001-3938(2008)03-0058-03]
点击复制

基于上下位机的中频弯管机控制系统
分享到:

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
31
期数:
2008年第3期
页码:
58-60
栏目:
工艺与设备
出版日期:
2008-05-28

文章信息/Info

Title:
Medium-frequency Bending Pipe System Based on up and down Computer
文章编号:
1001-3938(2008)03-0058-03
作者:
徐   刚杨   东廖广平纪海涛
(中油集团渤海石油装备制造有限公司)
Author(s):
XU GangYANG DongLIAO Guang-pingJI Hai-tao
关键词:
中频弯管控制系统PLCWinCC
Keywords:
medium-frequency bending pipecontrol systemPLCWINCC
分类号:
TP273.5
DOI:
1001-3938(2008)03-0058-03
文献标志码:
B
摘要:
基于上下位机中频弯管机组的自动监控系统按结构分为信息管理、控制和设备三层,系统采用IPC+PLC的上下位机的结构,其中下位机PLC作为现场级的控制设备,用于数据采集和控制;上位机IPC利用工控组态软件完成过程数据的存储、处理、分析及人机交互界面。介绍了控制系统中温度测量、恒温控制、工艺参数记录储存、历史数据查询等设计方案及工作中应注意事项。使用证明,该系统工艺一致性好,基本实现了自动控制。
Abstract:
The medium-frequency bending pipe system based on up and down computer consists of information management,control and equipment.The system adopt IPC+PLC up and down computer structure,and down computer PLC is as spot control equipment using for collecting data and controlling;Up computer IPC utilizes process-controller configuration software to finish process data storage,disposal and analysis,as well as manmachine exchange interface.This paper introduced control temperature,constant temperature control,record and storage of procedure parameter and historical data tracing,as well as design method.In addition to,it also mentioned caution proceedings during operation.Facts proved that this system procedure is with good consistency,and basically realize automatic control.

参考文献/References:

[1]西门子(中国)有限公司自动化与驱动集团.深入浅出西门子WinCC V6[M].北京:北京航空航天大学出版社,2004.
[2]邵作之.中频弯管工艺中测温的分析及应用[J].河北电力技术,1997,16(5):12-16.

相似文献/References:

[1]钱 镇,崔 旭.DFJ-F-G7新型飞锯控制系统[J].焊管,2008,31(3):51.[doi:1001-3938(2008)03-0051-05]
 QIAN Zheng,CUI Xu.Control System of DFJ-F-G7 New Type Flying Saw[J].,2008,31(3):51.[doi:1001-3938(2008)03-0051-05]
[2]徐 刚,郝永伟,高振宇,等.基于上下位机的中频弯管机控制系统(续)[J].焊管,2008,31(4):60.[doi:1001-3938(2008)04-0060-02]
 XU Gang,HAO Yong-wei,GAO Zhen-yu,et al.Medium-frequency Bending Pipe System Based on up and down Computer(Continued)[J].,2008,31(3):60.[doi:1001-3938(2008)04-0060-02]
[3]金奎文.新型在线全自动不锈钢氩弧焊管焊缝辊轧机的研制[J].焊管,2009,32(6):42.[doi:1001-3938(2009)06-0042-04]
 JIN Kui-wen.Research on Weld Roller Machine of New Type on-line Automatic Stainless Argon Arc Welding[J].,2009,32(3):42.[doi:1001-3938(2009)06-0042-04]
[4]徐刚,吴亚军,徐强,等.基于SINAMICS S120的管端倒棱机控制系统[J].焊管,2010,33(9):38.[doi:1001-3938(2010)09-0038-03]
 XU Gang,WU Ya-jun,XU Qiang,et al.Control System of Pipe End Chamfering Machine Based on SINAMICS S120[J].,2010,33(3):38.[doi:1001-3938(2010)09-0038-03]
[5]陈 亮,闵建东,刘建杰.直缝焊管预弯机数控系统的改造[J].焊管,2016,39(3):46.[doi:10.19291/j.cnki.1001-3938.2016.03.010]
 CHEN Liang,MIN Jiandong,LIU Jianjie.Numerical Control System Reform of Longitudinal Welded Pipe Prebending Machine[J].,2016,39(3):46.[doi:10.19291/j.cnki.1001-3938.2016.03.010]
[6]孙仁俊.连续油管注入头液压同步控制系统设计[J].焊管,2017,40(9):21.[doi:10.19291/j.cnki.1001-3938.2017.09.005]
 SUN Renjun.Design of Hydraulic Synchronous Control System for Coiled Tubing Injection Head[J].,2017,40(3):21.[doi:10.19291/j.cnki.1001-3938.2017.09.005]
[7]李 刚,杜强娜,张洪坤,等.倒棱机床身进给伺服控制系统的改进[J].焊管,2017,40(10):52.[doi:10.19291/j.cnki.1001-3938.2017.10.009]
 LI Gang,DU Qiangna,ZHANG Hongkun,et al.Servo Control System Improvement of Lathe Bed Feeding of Welded Pipe Chamfering Machine[J].,2017,40(3):52.[doi:10.19291/j.cnki.1001-3938.2017.10.009]
[8]周好斌,付新宇,刘嘉琪,等.基于PLC的钢筋钢带焊接生产线控制系统设计[J].焊管,2018,41(12):26.[doi:10.19291/j.cnki.1001-3938.2018.12.005]
 ZHOU Haobin,FU Xinyu,LIU Jiaqi,et al.Design of Welding Line Control System for Steel Strip Based on PLC[J].,2018,41(3):26.[doi:10.19291/j.cnki.1001-3938.2018.12.005]

备注/Memo

备注/Memo:
徐刚(1973-),男,工学硕士,工程师,主要研究方向为机电系统控制及自动化,自动化装置与智能控制系统。
收稿日期:2007-10-23
修改稿收稿日期:2007-11-06
更新日期/Last Update: