[1]郭宏侠,尹长华.中厚度钢板单面焊全熔透焊缝焊接技术[J].焊管,2008,31(6):69-71.[doi:1001－3938（2008）06－0069－03]
　GUO Hong-xia,YIN Chang-hua.Welding Technology of One Side Full Penetration Welding for Heavy Plate[J].,2008,31(6):69-71.[doi:1001－3938（2008）06－0069－03]
点击复制

中厚度钢板单面焊全熔透焊缝焊接技术
分享到：

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
31
期数:
2008年第6期
页码:
69-71
栏目:
经验交流
出版日期:
2008-11-28

文章信息/Info

Title:
Welding Technology of One Side Full Penetration Welding for Heavy Plate
文章编号:
1001－3938（2008）06－0069－03
作者:
郭宏侠1; 尹长华2
（1.鞍钢重机公司金属结构厂；2.中国石油管道科学研究院）
Author(s):
GUO Hong-xia; YIN Chang-hua
关键词:
单面焊; 全熔透; 探伤; 焊接参数
Keywords:
one side welding; full penetration; UT check; welding procedure
分类号:
TG441.4
DOI:
1001－3938（2008）06－0069－03
文献标志码:
A
摘要:
目前国内设计很少应用大量的中、厚钢板单面焊全熔透焊缝，也几乎没有能够满足此种焊缝质量要求的金属结构件制作厂家，多数厂家即使是压力容器专业制造厂，在焊接此类焊缝时，也会存在不同程度的焊缝根部未熔合或未焊透，通过采取新型焊接工艺，反复试验，不断改进，最终保证了此类焊缝UT探伤时焊缝有效深度≥板厚，UT探伤一次合格率达90%以上，有效地保证了此类焊缝的焊接质量，同时也大大提高了生产效率。
Abstract:
At present in China,one side full penetration welding of heavy plate are rarely designed and nealy no metal construction manufacture can satisfy this request without any defact after welding UT check.Almost manufactures even press vessel manufactures will occur no penetration differently at the bottom of welds and couldn’t  guarantee the depth of qualified welds are not smaller than the thick of plate.In this article,by using new welding procedure,continuous test and development,we guaranteed at last the effective weld depth is equal or bigger than the thick of plate.By using this method,the coefficient of qualified welds at first UT check reached more than 90%.That is to say,the quality of this welding get much better.At the same time,the productivity get much higher.

参考文献/References:

［1］ASME锅炉及压力容器规范(第Ⅸ卷)：1998年，焊接和钎焊评定［S］.
［2］中国机械工程学会焊接学会.焊接手册 第2册［M］.北京：机械工业出版社，2001.

相似文献/References:

[1]杨晓哲.钻机结构件K形坡口全熔透焊缝焊接质量控制[J].焊管,2016,39(10):66.[doi:DOI: 10.19291/j.cnki.1001-3938.2016.10.016]
　YANG Xiaozhe.Welding Quality Control of Drilling Rig Structural ComponentK Shape Groove Full Penetration Weld[J].,2016,39(6):66.[doi:DOI: 10.19291/j.cnki.1001-3938.2016.10.016]

备注/Memo

备注/Memo:
郭宏侠，女，工程师，从事焊接技术研究、工艺评定与技术管理工作。
收稿日期：2008－04－28
更新日期/Last Update: