[1]刘明,胡德虎.螺旋埋弧焊管预精焊预焊气孔成因及解决措施[J].焊管,2023,46(5):60-64.[doi:10.19291/j.cnki.1001-3938.2023.05.009]
 LIU Ming,HU Dehu.Causes and Solution Measures of Pre?elding Gas Holes in Pre finishing Welding of Submerged?rc Welded Helical Pipe[J].,2023,46(5):60-64.[doi:10.19291/j.cnki.1001-3938.2023.05.009]
点击复制

螺旋埋弧焊管预精焊预焊气孔成因及解决措施()
分享到:

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
46
期数:
2023年第5期
页码:
60-64
栏目:
经验交流
出版日期:
2023-05-28

文章信息/Info

Title:
Causes and Solution Measures of Pre?elding Gas Holes in Pre finishing Welding of Submerged?rc Welded Helical Pipe
文章编号:
10.19291/j.cnki.1001-3938.2023.05.009
作者:
刘明胡德虎
1. 中油宝世顺(秦皇岛)钢管有限公司,河北 秦皇岛 066206; 2. 宝鸡石油输送管有限公司,陕西 宝鸡 721008
Author(s):
LIU Ming HU Dehu
1. Zhongyou Baoshishun (Qinhuangdao) Pipe Co., Ltd., Qinhuangdao 066206, Hebei, China; 2. Petroleum Steel Pipe Co., Ltd., Baoji 721008, Shaanxi, China
关键词:
螺旋预精焊焊缝成形气孔缺陷高速MAG焊
Keywords:
helical pre finishing welding weld forming gas hole defects high speed MAG welding
分类号:
TG434
DOI:
10.19291/j.cnki.1001-3938.2023.05.009
文献标志码:
B
摘要:
为了解决螺旋埋弧焊管预焊焊缝气孔缺陷,提高精焊埋弧焊缝质量,通过对预焊气孔产生原因和焊接工艺进行分析,提出了预焊焊缝气孔的预防措施。结果表明,预焊焊缝出现气孔的主要原因是空气混入保护气体以及坡口两侧存在铁锈;在熔池凝固过程中,在焊缝表面和内部产生气孔,最终在预焊焊缝成形后形成气孔缺陷。在钢管预焊焊接时采用高Si/Mn元素焊丝、控制保护气体比例及流量、严格执行合缝间隙和坡口清洁等措施均可避免预焊焊缝气孔的产生,从而提高焊管质量。
Abstract:
In order to solve the pre welding gas hole defects of submerged arc welded helical pipe and improve the quality of submerged arc weld, the causes of the pre welding gas hole and the welding process were analyzed, and the measures to solve the pre welding gas hole were put forward. The results show that the main causes of porosity in the pre welding seam are air mixing into shielding gas and rust on both sides of groove. During the solidification of the melt pool, gas holes are generated on the surface and inside of the weld, ultimately forming gas hole defects after the pre welding seam is formed. High Si/Mn wire, control of shielding gas proportion and flow rate, strict implementation of clearance between welds and groove cleaning can prevent weld gas hole during pre welding of helical steel pipe, improve the quality of welded pipe.

参考文献/References:

[1] 付超,杨振铎,罗天宝.螺旋缝埋弧焊管预精焊生产线全自动精焊设备[J].现代焊接,2014(12):34-37.[2] 毛周团,尹志远,王少华,等.螺旋埋弧焊管预精焊生产工艺[J].焊管,2010,33(3):52-55.[3] 韩显柱,胡德虎,螺旋埋弧焊管预焊焊接设备与工艺[J].焊管,2010,33(11):47-50.[4] 杨战利,张善保,杨永波,等.新形大电流空冷MAG焊枪研制[J].焊管,2012,35(2):27-29,33.[5] 张幻.CO2气体保护焊焊接工艺及应用[J].船海工程,2008(1):46-48.[6] 李亚江,王娟.焊接缺陷分析及对策(第二版)[M].北京:化学工业出版社,2014.[7] 杨战利,张善保,杨永波,等.粗丝高速MAG焊驼峰焊道形成机理研究[J].焊接学报,2013,34(1):61-64.[8] 王克鸿,游秋榕,沈莹吉.基于视觉的MAG焊气孔缺陷图像特征初步探讨[J].焊接学报,2006,27(12):13-16.[9] 周晋元,任芸.CO2气体保护焊几个问题的探讨[J].煤矿机械,2008(9):105.[10]仝钢.CO2气体保护焊在中厚板焊接中产生气体的预防[J]. 同煤科技,2004(2):15-16.[11] 李践桥, 刘志强, 王利,等.关于保护气流量对MAG焊气孔产生率影响的研究[J].金属加工,2014(S2):223-225.[12] 周岩,杨战立,唐麒龙.螺旋焊管精焊焊缝常见缺陷及预防措施[J].焊管,2013,36(5):58-61.[13] 王凤成,崔晓峰,王国胜.螺旋缝焊管预焊缺陷对精焊质量的影响和控制[J].质量控制,2012,41(2):49-52.[14] 张文斌.海底输油直缝钢管焊接气孔成因分析及控制措施[J].焊接,2003(10):29-32.[15] 唐子金.螺旋埋弧焊管预精焊质量控制方法讨论[J].焊管,2011,34(2):26-29.

相似文献/References:

[1]尹志远,周 岩,李 颖,等.预精焊工艺对螺旋埋弧焊管内焊“马鞍型”焊缝的控制[J].焊管,2012,35(1):40.[doi:1001-3938(2012)01-0040-04]
 YIN Zhi-yuan,ZHOU Yan,LI Ying,et al.Control “Saddle-shaped” Inside Weld of SAWH Pipe by Adopting Two-step Welding Process[J].,2012,35(5):40.[doi:1001-3938(2012)01-0040-04]
[2]王海力.螺旋埋弧焊管外焊缝形状控制技术探讨[J].焊管,2012,35(2):56.[doi:1001-3938(2012)02-0056-06]
 WANG Hai-li.Discussion on Control Outside Weld Profile of SAWH Pipe[J].,2012,35(5):56.[doi:1001-3938(2012)02-0056-06]
[3]王兴山,苟世峰,王 刚,等.螺旋埋弧预精焊内焊焊缝及HAZ硬度试验研究[J].焊管,2015,38(12):33.[doi:1001-3938(2015)12-0033-07]
 WANG Xingshan,GOU Shifeng,WANG Gang,et al.Research on Spiral Two-steps Welding Inside Weld and HAZ Hardness Test[J].,2015,38(5):33.[doi:1001-3938(2015)12-0033-07]
[4]毛锦荣,陈星斌,周叶平,等.316L不锈钢电子束锁底焊接接头成形及显微组织[J].焊管,2018,41(11):17.[doi:10.19291/j.cnki.1001-3938.2018.11.004]
 MAO Jinrong,CHEN Xingbin,ZHOU Yeping,et al.Formation and Microstructure of Electron Beam Lock Bottom Welded Joints of 316L Stainless Steel[J].,2018,41(5):17.[doi:10.19291/j.cnki.1001-3938.2018.11.004]
[5]刘宏博,刘彦明,杨战利,等.起焊位置对连续油管全位置自动焊焊缝成形的影响[J].焊管,2019,42(12):33.[doi:10.19291/j.cnki.1001-3938.2019.12.007]
 LIU Hongbo,LIU Yanming,YANG Zhanli,et al.Effect of Starting Welding Position on All-position Automatic WeldingForming of Coiled Tubing[J].,2019,42(5):33.[doi:10.19291/j.cnki.1001-3938.2019.12.007]
[6]杜振宾,王卫玲,熊 然.TC18钛合金薄壁壳体真空电子束焊接形性控制研究[J].焊管,2020,43(10):29.[doi:10.19291/j.cnki.1001-3938.2020.10.005]
 DU Zhenbin,WANG Weiling,XIONG Ran.Study on the Weld Shape and Performance Control of Vacuum Electron Beam Welding of TC18 Titanium Alloy Thin-walled Shell[J].,2020,43(5):29.[doi:10.19291/j.cnki.1001-3938.2020.10.005]
[7]郭龙龙,王宏,付堃,等.天然气管道在役焊接熔池流动行为及成形研究[J].焊管,2023,46(9):1.[doi:10.19291/j.cnki.1001-3938.2023.09.001]
 GUO Longlong,WANG Hong,FU Kun,et al.Study on Flow Behavior and Forming of Welding Molten Pool of Natural Gas Pipeline in Service[J].,2023,46(5):1.[doi:10.19291/j.cnki.1001-3938.2023.09.001]

备注/Memo

备注/Memo:
收稿日期:2022-07-05作者简介:刘明(1984—),本科,工程师,主要从事螺旋预精焊钢管焊接工艺及装备研究工作。
更新日期/Last Update: 2023-05-23