[1]王伟,朱林,胡平,等.针状铁素体管线钢的组织结构及其与力学性能的关系研究[J].焊管,2009,32(11):21-28.[doi:1001－3938（2009）11－0021－08]
　WANG Wei,ZHU Lin,HU Ping,et al.Study on Microstructures and the Relation Between Microstructures and Mechanical Properties of Acicular Ferrite Pipeline Steel[J].,2009,32(11):21-28.[doi:1001－3938（2009）11－0021－08]
点击复制

针状铁素体管线钢的组织结构及其与力学性能的关系研究
分享到：

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
32
期数:
2009年第11期
页码:
21-28
栏目:
试验与研究
出版日期:
2009-11-28

文章信息/Info

Title:
Study on Microstructures and the Relation Between Microstructures and Mechanical Properties of Acicular Ferrite Pipeline Steel
文章编号:
1001－3938（2009）11－0021－08
作者:
王伟1; 2; 朱林2; 胡平2; 单以银2; 杨柯2
（1.广东电网公司电力科学研究院，广州 510600；2.中国科学院金属研究所，沈阳 110016）
Author(s):
WANG Wei1; 2; ZHU Lin2; HU Ping2; SHAN Yi-yin2; YANG Ke2
（1.Electric Power Research Institute of Guangdong Power Grid Corporation,Guangzhou 510600,China；2.Institute of Metal Research,Chinese Academy of Sciences,Shenyang 110016,China）
关键词:
针状铁素体; 管线钢; 显微组织; 力学性能
Keywords:
acicular ferrite; pipeline steel; microstructure; mechanical property
分类号:
TG142.1
DOI:
1001－3938（2009）11－0021－08
文献标志码:
A
摘要:
基于控轧控冷工艺研究，在化学成分相同的超低碳微合金管线钢中获得了不同组成比的针状铁素体（AF）复相组织，探讨了其与力学性能的关系。结果表明：①降低终轧温度导致有效晶粒尺寸明显减小，冷却速度和模拟卷取温度的变化对有效晶粒尺寸影响不大；②降低终轧温度，提高冷速，会促进AF复相组织中粒状贝氏体铁素体（GF）、贝氏体铁素体(BF)等低温组织含量的增加，提高模拟卷取温度增强的析出强化效果不如降低终轧温度导致的AF低温组织含量提高和晶粒细化对强度提高的贡献大；③随着终轧温度的下降，大角度晶界含量先提高后降低，在相变点以上40℃附近达到最高值，大角度晶界含量越高，低温韧性越好；④当管线钢获得较高BF和GF含量、低的准多边形铁素体（QF）含量组成的细小AF组织时，综合力学性能优良。
Abstract:
Based on the study of controlled rolling and conrtolled cooling,the acicular ferrite (AF) microstructures with different phase components were obtained in an ultralowcarbon microalloyed pipeline steel with the same chemical composition,and the relation between AF microstructures and mechanical properties was investigated.The results showed that:①the effective grain size(EGS) in the steel reduced obviously with decreasing finish rolling temperature(FRT),but did not change obviously with cooling rate(CR) and simulated coiling temperature (SCT) in the experiment;②Lowering FRT or enhancing CR could increase the percentage of granular bainitic ferrite(GF) and bainitic ferrite(BF) in AF,and the increasing percentage of GF and BF and fine grains make more contribution to the increase of strength than increasing precipitation by enhancing SCT;③The content of high angle grain boundaries increased firstly,then decreased and reached the top at FRT of about 40℃ above Ar3.It was found that the higher the fraction of HAGBs was, the better the low temperature toughness was;④When fine AF microstructure was obtained with high GF and BF content and low quasi-polygonal ferrite (QF) content,the pipeline steel could possess good mechnical property.

参考文献/References:

［1］SMITH Y E,COLDREN A P,CRYDERMAN R L.Mn-Mo-Nb Acicular Ferrite Steels with High Strength and Toughness［C］∥Toward Improved Ductility and Toughness,Tokyo:Climax Molybdenum Co.Ltd.,1972:119-142.
［2］COLDREN A P,SMITH Y E,CRYDERMAN R L.Microstructure and Properties of Low C Mn-Mo-Nb Steels［C］∥Processing and Properties of Low Carbon Steel,New York:AIME,1973:163-189.
［3］SMITH Y E,COLDREN A P,CRYDERMAN R L.Highstrength,Ductile Mn-Mo-Nb Steels with a Structure of Acicular Ferrite［J］.Met Sci Heat Treat(English Translation of Metallovedenie i Termicheskaya Obrabotka Metallov),1976,18(1-2):59-65.
［4］TANAKA T.Controlled Rolling of Steel Plate and Strip［J］.Int Met Rev,1981,26(4):185-212.
［5］LEE J L,HON M H,CHENG G H.The Intermediate Transformation of Mn-Mo-Nb Steel during Continuous Cooling［J］.J Mater Sci,1987,22(8):2767-2777.
［6］赵明纯，单以银，曲锦波，等.控制热加工下管线钢中针状铁素体的形成［J］.金属学报，2001,37(8)：820-824.
［7］赵明纯，肖福仁，单以银，等.超低碳针状铁素体管线钢的显微特征及强韧性行为［J］.金属学报，2002,38(3)：283-287.
［8］王仪康，杨柯，单以银.高压输气管线用钢［J］.焊管，2002,25(1)：1-10.
［9］〖ZK（〗王仪康，杨柯，单以银，等. 我国高压输送管线钢的发展［C］∥石油天然气管道建设与技术论坛会，廊坊：石油出版社，2002:18-38.
［10］ZHAO M C,TANG B,SHAN Y Y,et al.Role of Microstructure on Sulfide Stress Cracking of Oil and Gas Pipeline Steels［J］.Metall Mater Trans,2003,34A(5):1089-1096.

相似文献/References:

[1]李新华,罗金恒,赵新伟,等.高钢级管线钢失效评估曲线研究[J].焊管,2007,30(4):33.[doi:1001－3938（2007）04－0033－03]
　LI Xin-hua,LUO Jin-heng,ZHAO Xin-wei,et al.Research on Failure Assessment Curves of High Grade Pipeline Steel[J].,2007,30(11):33.[doi:1001－3938（2007）04－0033－03]
[2]宫少涛,王爱民,吉玲康,等.X80与X100级管线钢屈服强度Rt 0.5与Rp 0.2的差异性研究[J].焊管,2007,30(5):42.[doi:1001－3938（2007）05－0042－03]
　GONG Shao-tao,WANG Ai-min,JI Ling-kang,et al.Study on Difference Between Yield Strength Rt 0.5 and Rp 0.2 for X80 and X100 Pipelines Steel[J].,2007,30(11):42.[doi:1001－3938（2007）05－0042－03]
[3]刘庆才,李 东,黎剑锋.影响输气管线钢管抗H2S性能主要因素的探讨[J].焊管,2007,30(5):54.[doi:1001－3938（2007）05－0054－05]
　LIU Qing-cai,LI Dong,LI Jian-feng.Key Factors Affecting Sour Service Ability of Welded Pipe and Its Domestic Production[J].,2007,30(11):54.[doi:1001－3938（2007）05－0054－05]
[4]王树人,崔志新.管线钢落锤撕裂试验异常脆性断口分析[J].焊管,2007,30(6):69.[doi:1001－3938（2007）06－0069－03]
　WANG Shu-ren? CUI Zhi-xin.Analysis on Abnormal Brittle Fracture of DWTT for Pipeline Steel[J].,2007,30(11):69.[doi:1001－3938（2007）06－0069－03]
[5]黄明浩,徐 烽,黄国建.影响管线钢屈强比的因素探讨[J].焊管,2008,31(3):20.[doi:1001－3938（2008）03－0020－04]
　HUANG Ming-hao,XU Feng,HUANG Guo-jian.Discussion on Influencing Factors of Yield Ratio for Pipeline Steel[J].,2008,31(11):20.[doi:1001－3938（2008）03－0020－04]
[6]牛 辉,余大涛,高惠临.管线钢焊接热影响区的组织预测[J].焊管,2008,31(3):28.[doi:1001－3938（2008）03－0028－05]
　NU Hui,YU Da-tao,GAO Hui-lin.Structure Forecast of Pipeline Steel Welding Heat Affected Zone[J].,2008,31(11):28.[doi:1001－3938（2008）03－0028－05]
[7]郑 中,赵 迪,禹文涛.本钢高Nb X70管线钢的生产实践[J].焊管,2008,31(5):54.[doi:1001－3938（2008）05－0054－05]
　ZHENG Zhong,ZHAO Di,YU Wen-tao.Production Practice of X70 Grade Pipeline Steel with High Content of Nb in Benxi Iron&Steel (Group) Co.Ltd[J].,2008,31(11):54.[doi:1001－3938（2008）05－0054－05]
[8]孔君华,郑 琳,关 云,等.西气东输二线工程用18.4 mm厚 X80级热轧板卷生产实践[J].焊管,2008,31(6):50.[doi:1001－3938（2008）06－0050－04]
　KONG Jun-hua,ZHENG Ling,GUAN Yun,et al.Production Experience of X80 Grade Hot Rolled Coil with 18.4 mm Thickness Used〖JZ〗for the Second West to East Gas Pipeline Project[J].,2008,31(11):50.[doi:1001－3938（2008）06－0050－04]
[9]黄国建,张英慧,孔祥磊,等.特厚规格X70和X80级热轧卷板的开发与应用[J].焊管,2009,32(2):17.[doi:1001－3938（2009）02－0017-06]
　HUANG Guo-jian,ZHANG Ying-hui,KONG Xiang-lei,et al.Development and Application of X70 & X80 Grade HRC with Heavy Thickness[J].,2009,32(11):17.[doi:1001－3938（2009）02－0017-06]
[10]杨专钊,李云龙,邓波,等.管线钢拉伸试验中异常屈服强度研究与分析[J].焊管,2009,32(4):51.[doi:1001－3938（2009）04－0051－03]
　YANG Zhuan-zhao,LI Yun-long,DENG Bo,et al.Research and Analysis of Abnormal Yield Strength during Tensile Test of Pipeline Steel[J].,2009,32(11):51.[doi:1001－3938（2009）04－0051－03]
[11]陶 鹏,张 弛,杨志刚,等.高钢级管线钢的组织和力学性能[J].焊管,2008,31(2):19.[doi:1001－3938（2008）02－0019－04]
　TAO Peng,ZHANG Chi,YANG Zhi-gang,et al.The Microstructure and Mechanical Property of X70,X80 and X100 Grade Pipeline Steel[J].,2008,31(11):19.[doi:1001－3938（2008）02－0019－04]
[12]彭涛,高惠临.管线钢显微组织的基本特征[J].焊管,2010,33(7):5.[doi:1001－3938（2010）07－0005－06]
　PENG Tao,GAO Hui-lin.Microstructure Characteristics of Pipeline Steels[J].,2010,33(11):5.[doi:1001－3938（2010）07－0005－06]

备注/Memo

备注/Memo:
作者简介：王伟（1983-），男，博士，主要从事金属材料的热加工工艺、显微组织和力学性能的相关方面研究。
收稿日期：2009－05－17
修改稿收稿日期：2009－09－21
更新日期/Last Update: