[1]胡德虎,赵 炜,牛 辉,等.螺旋埋弧焊管双丝高速焊工艺参数的优化[J].焊管,2007,30(4):69-71.[doi:1001-3938(2007)04-0069-03]
 HU De-hu,ZHAO Wei,NIU Hui,et al.Process Parameters Optimization of High Speed Welding with Double Wires for Spiral Submerged Arc Welded Pipe[J].,2007,30(4):69-71.[doi:1001-3938(2007)04-0069-03]
点击复制

螺旋埋弧焊管双丝高速焊工艺参数的优化
分享到:

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
30
期数:
2007年第4期
页码:
69-71
栏目:
经验交流
出版日期:
2007-07-28

文章信息/Info

Title:
Process Parameters Optimization of High Speed Welding with Double Wires for Spiral Submerged Arc Welded Pipe
文章编号:
1001-3938(2007)04-0069-03
作者:
胡德虎赵 炜牛 辉张 峰
(宝鸡石油钢管有限责任公司)
Author(s):
HU De-huZHAO WeiNIU HuiZHANG Feng
关键词:
螺旋埋弧焊管双丝焊坡口形式偏心距焊丝间距焊丝倾角焊丝伸长量
Keywords:
spiral submerged arc welded pipedouble wires weldinggroove typeeccentricitydistance between welding wiresangle of welding wireelongation of welding wire
分类号:
TG406
DOI:
1001-3938(2007)04-0069-03
文献标志码:
B
摘要:
详细介绍了双丝螺旋埋弧焊各种工艺参数的优化与选择,提出:采用直流+交流的焊接方式匹配;钢带边缘铣成不对称X形坡口;内焊偏心距只能控制在0~30mm,外焊偏心距稍大于内焊偏心距;内外焊丝间距一样;内外焊焊丝倾角基本一样,前丝为3°~6°,后丝为8°~13°;内外焊焊丝伸长量一样。对双丝焊的内、外焊电流和电压的选配原则作了着重说明。并指出了提高双丝焊质量的控制要点。
Abstract:
This article introduces optimization and selection of each process parameter for spiral submerged arc welding with double wires in detail and proposes to adopting matched direct current plus alternative current welding method,to milling strip edges with dissymmetry X-bevel,to controlling eccentricity distance of inside welding only within 0~30mm and eccentricity distance of outside welding slightly larger than that of inside welding as well as keeping same distance between welding wires for outside and inside welding and same angle of welding for outside and inside welding,and angle of front wire is 3°~6°and angle of back wire is 8°~13°,same elongation of welding wire for outside and inside welding. It also emphasizes selection and matching principle of inside and outside welding current and voltage to double wires and puts forward to control points of improving quality of double wires welding.

参考文献/References:

[1]周朝伟.焊工手册[M].北京:机械工业出版社,2001.
[2]王海力.较高焊速下螺旋管质量控制技术的探讨[J].焊管,2005,28(4):67-70.

相似文献/References:

[1]刘 云,彭春明,刘德应.螺旋焊管内焊双丝焊装置的设计与应用[J].焊管,2007,30(4):51.[doi:1001-3938(2007)04-0051-03]
 LIU Yun,PENG Chun-ming,LIU De-ying.Design and Application of Inside Welding Double Wires Welding Unit for Spiral Submerged Arc Welding Pipe[J].,2007,30(4):51.[doi:1001-3938(2007)04-0051-03]
[2]杨 志 孝.一种简单实用的螺旋埋弧焊管内焊清渣机[J].焊管,2007,30(5):63.[doi:1001-3938(2007)05-0063-03]
 YANG Zhi-xiao.New & Practical Welding Slag Cleaning Unit for Inside Welding of Helical Submerged Arc Welding Pipe[J].,2007,30(4):63.[doi:1001-3938(2007)05-0063-03]
[3]李必文,杨春雨,王树人,等.带钢边缘加工工艺的改进——双铣边替代剪边[J].焊管,2008,31(2):63.[doi:1001-3938(2008)02-0063-04]
 LI Bi-wen,YANG Chun-yu,WANG Shu-ren,et al.Improvement of Machining Process for Strip Edges-replacing Edges Cutting with Double Milling[J].,2008,31(4):63.[doi:1001-3938(2008)02-0063-04]
[4]秦跃平.前摆式螺旋埋弧焊管机组内焊缝裂纹产生原因分析[J].焊管,2008,31(4):62.[doi:1001-3938(2008)04-0062-02]
 QIN Yue-ping.Analysis on Reason of Inside Weld Crack of Front Swing SSAW Pipe Units[J].,2008,31(4):62.[doi:1001-3938(2008)04-0062-02]
[5]林春明,徐泽旋,朱文闯,等.螺旋埋弧焊管焊缝中链状气孔的判定[J].焊管,2008,31(4):69.[doi:1001-3938(2008)04-0069-03]
 LIN Chun-ming,XU Ze-xuan,ZHU Wen-chuang,et al.Verification to Chain Porosity in Weld of SSAW Pipe[J].,2008,31(4):69.[doi:1001-3938(2008)04-0069-03]
[6]李为卫,王亚龙,李 洋,等.小批量试制X80级板卷及焊管的拉伸性能分析[J].焊管,2008,31(5):16.[doi:1001-3938(2008)05-0016-04]
 LI Wei-wei,WANG Ya-long,LI Yang,et al.Analysis on Tensile Properties of Small Batch Trial-produced X80 Grade Steel Coil and Welded Pipe[J].,2008,31(4):16.[doi:1001-3938(2008)05-0016-04]
[7]宗 波,王树人,王铁民,等.国产X80级螺旋埋弧焊管的试制[J].焊管,2008,31(6):39.[doi:1001-3938(2008)06-0039〖KG-*2〗-04]
 ZONG Bo,WANG Shu-ren,WANG Tie-min,et al.Trial Production of X80 Grade Helically Submerged Arc Welded Pipe in China[J].,2008,31(4):39.[doi:1001-3938(2008)06-0039〖KG-*2〗-04]
[8]陈小康,张毅.螺旋埋弧焊管生产过程卷板消耗定额编制方法及应用[J].焊管,2009,32(5):70.[doi:1001-3938(2009)05-0070-03]
 CHEN Xiao-kang,ZHANG Yi.Formulate Steel Coil Consumption Quota Method During SSAW Pipe Production and Its Application[J].,2009,32(4):70.[doi:1001-3938(2009)05-0070-03]
[9]孟德强,宁月,徐辉.螺旋埋弧焊管常见焊接裂纹的分析[J].焊管,2009,32(7):58.[doi:1001-3938(2009)07-0058-04]
 MENG De-qiang,NING Yue,XU Hui.Analysis on Common Welding Crack of SSAW Pipe[J].,2009,32(4):58.[doi:1001-3938(2009)07-0058-04]
[10]吴在盛,赵国仙,马长权.X80级螺旋埋弧焊管用高强度高韧性烧结焊剂的研制[J].焊管,2009,32(10):22.[doi:1001-3938(2009)10-0022-04]
 WU Zai-sheng,ZHAO Guo-xian,MA Chang-quan.Development of High Strength and High Toughness Sintered Flux Used in X80 Grade SSAW Pipe[J].,2009,32(4):22.[doi:1001-3938(2009)10-0022-04]
[11]毕宗岳,王海博,王高峰.螺旋埋弧焊管焊缝形貌优化研究[J].焊管,2008,31(2):14.[doi:1001-3938(2008)02-0014-05]
 BI Zong-yue,WANG Hai-bo,WANG Gao-feng.Optimization Research on Weld Profile of Spiral Submerged Arc Welded Pipe[J].,2008,31(4):14.[doi:1001-3938(2008)02-0014-05]

备注/Memo

备注/Memo:
胡德虎(1964-),男,中国石油物资装备总公司高级技师,从事螺旋埋弧焊管焊接工作多年。
更新日期/Last Update: