[1]蔡洪能,李望南,韩雪成.钛合金厚板焊接接头残余应力测试[J].焊管,2018,41(11):1-5.11.[doi:10.19291/j.cnki.1001-3938.2018.11.001]
　CAI Hongneng,LI Wangnan,HAN Xuecheng.Residual Stress Test of Welded Joints of Titanium Alloy Thick Plates[J].,2018,41(11):1-5.11.[doi:10.19291/j.cnki.1001-3938.2018.11.001]
点击复制

钛合金厚板焊接接头残余应力测试()
分享到：

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
41
期数:
2018年第11期
页码:
1-5.11
栏目:
试验与研究
出版日期:
2018-11-28

文章信息/Info

Title:
Residual Stress Test of Welded Joints of Titanium Alloy Thick Plates
文章编号:
10.19291/j.cnki.1001-3938.2018.11.001
作者:
蔡洪能; 李望南; 韩雪成
 西安交通大学 金属材料强度国家重点实验室，西安 710049
Author(s):
CAI Hongneng;  LI Wangnan;  HAN Xuecheng
State Key Laboratory for Mechanical Behavior of Materials，Xi’an Jiaotong University，Xi’an 710049，China
关键词:
钛合金厚板; 焊接接头; 有限元标定; 三维残余应力
Keywords:
titanium alloy thick plate;  welding joint;  the finite element calibration;  the three dimensional residual stresses
分类号:
TG404
DOI:
10.19291/j.cnki.1001-3938.2018.11.001
文献标志码:
A
摘要:
采用局部逐层对称剥削材料盲孔法对51 mm厚钛合金Ti80板焊接接头残余应力进行了测试，并系统研究了其三维残余应力分布特征。结果表明，局部逐层剥削材料盲孔法能有效测量大厚度焊接件焊接接头的内部残余应力，并能准确反映大梯度变化应力状态。钛合金焊接接头，沿垂直焊缝方向在距焊缝中心-10~10 mm范围内，具有较高拉应力，应力值集中在500 MPa左右，且拉应力峰值出现在上表面距离焊缝中心10 mm位置；沿厚度方向距焊缝中心-10~10 mm范围内，为拉应力，表层应力普遍大于内部应力。在远离焊缝位置沿厚度方向为压应力，应力值为200~680 MPa，且峰值出现在距离上表面5 mm和焊缝中心20 mm位置处。
Abstract:
The residual stress of the welded joint of 51 mm thick titanium alloy Ti80 plate was tested by the blind hole method of local layer-by-layer symmetric stripping material, and the three-dimensional residual stress distribution characteristics were systematically studied. The results show that the blind hole method of local layer-by-layer symmetric stripping material can effectively measure the internal residual stress of welding joint of large thickness welding joint and accurately reflect the state of large gradient change stress. The welded joints of titanium alloy have a high tensile stress in the direction of the vertical weld in the range of -10~10 mm from the center of the weld. The stress value is concentrated at about 500 MPa, and the tensile stress peak appears on the upper surface from the center of the weld 10 mm. In the thickness direction from the center of the weld to the range of -10~10 mm, the tensile stress is generally greater than the internal stress.The compressive stress is in the thickness direction away from the weld position, the stress value is between 200 and 680 MPa, and the peak appears at a distance of 5 mm from the upper surface and 20 mm from the center of the weld.

参考文献/References:

[1] 彭艳萍，曾凡昌，王俊杰，等. 国外航空钛合金的发展应用及其特点分析[J]. 材料工程, 1997（10）: 3-6.
[2] 林丽化，陈立功， 顾明元．残余应力测量技术现状及其发展动向[J]． 机械，1998，25（5）: 46-49．
[3] DONG P, BRUST F W. Welding residual stresses and effects on fracture in pressure vessel and piping components: A millennium review and beyond[J]． Journal of Pressure Vessel Technology, 2000, 122（3）: 329-338．
[4] 裴怡，包亚峰，唐慕尧，等. 盲孔法测量精度的研究——边界及孔间距的影响[J]. 焊接学报, 1994, 15（3）:  191-196.
[5] 张旦闻，刘宏昭，刘平. 裂纹柔度法在7075铝合金板残余应力检测中的应用[J]. 材料热处理学报，2006, 27（2）: 127-136.
[6] 周新灵，张小伍，李兴东，等． 测试大型汽轮机转子残余应力的环芯法和X射线法[J]. 理化检测: 物理分册，2008, 44（4）：196-202.

相似文献/References:

[1]李鹤林,李 霄,吉玲康,等.油气管道基于应变的设计及抗大变形管线钢的开发与应用[J].焊管,2007,30(5):5.[doi:1001-3938（2007）05-0005-07]
　LI He-lin,LI Xiao,JI Ling-kang,et al.Strainbased Design for Pipeline and Development of Pipe Steels with High Deformation Resistance[J].,2007,30(11):5.[doi:1001-3938（2007）05-0005-07]
[2]尹长华,闫 臣.厚壁钢管自保护药芯焊丝半自动焊接头氢含量较高的原因及控制措施[J].焊管,2008,31(2):71.[doi:1001－3938（2008）02－0071－04]
　YIN Chang-hua,YAN Chen.Origin and Control Measure of Thick Wall Steel Pipe Welded Joint Contain Mach Hydrogen for Self-shielded Flux-cored Wire Semiautomatic Welding[J].,2008,31(11):71.[doi:1001－3938（2008）02－0071－04]
[3]许贵芝 编译.国外干线管道焊接接头的加热和热处理[J].焊管,2008,31(5):89.[doi:1001－3938（2008）05－0089－02]
　Edited and translated by XU Gui-zhi.Heating and Heat Treatment of Welding Jointer in the Abroad Trunk Pipeline[J].,2008,31(11):89.[doi:1001－3938（2008）05－0089－02]
[4]许贵芝 编译.俄罗斯不锈钢管道焊接接头的局部热处理[J].焊管,2009,32(1):61.[doi:1001－3938（2009）01－0061－04]
　Edited and Translated by XU Gui-zhi.Part Heat Treatment of Stainless Steel Pipeline Welding Joints in Russia[J].,2009,32(11):61.[doi:1001－3938（2009）01－0061－04]
[5]胡丽华,张雷,路民旭.1Cr低合金管线钢焊接接头组织和性能研究[J].焊管,2009,32(7):18.[doi:1001－3938（2009）07－0018－04]
　HU Li-hua,ZHANG Lei,LU Min-xu.Research on Microstructure and Mechanical Properties of1Cr Low Alloy Pipeline Steel Weld Joint[J].,2009,32(11):18.[doi:1001－3938（2009）07－0018－04]
[6]何小东,马秋荣,王长安,等.高强度管线钢焊接接头不同缺口位置的断裂韧性研究[J].焊管,2009,32(8):21.[doi:1001－3938（2009）08－0021－05]
　HE Xiao-dong,MA Qiu-rong,WANG Chang-an,et al.Fracture Toughness of Welded joints at Different Notch Location and Discussion of Specifications for High Strength line Pipe[J].,2009,32(11):21.[doi:1001－3938（2009）08－0021－05]
[7]苏丽珍,何莹,李桂芝,等.高强管线钢管道环焊缝高强匹配研究[J].焊管,2009,32(9):27.[doi:1001－3938（2009）09－0027－04]
　SU Li-zhen,HE Ying,LI Gui-zhi,et al.High Strength Matching Study on Circumferential Weld of High Grade Line Pipe[J].,2009,32(11):27.[doi:1001－3938（2009）09－0027－04]
[8]邵晓东,刘养勤,李瑛,等.X80钢管件焊接接头中Ni含量分析方法研究[J].焊管,2010,33(3):29.[doi:1001－3938（2010）0３－0029－04]
　SHAO Xiao-dong,LIU Yang-qin,LI Ying,et al.Study on Analytical Method for Nickel Contentin Welded Joints of X80 Grade Fittings[J].,2010,33(11):29.[doi:1001－3938（2010）0３－0029－04]
[9]王香云.12Cr1MoVG钢焊接接头热裂纹的原因分析及对策[J].焊管,2010,33(4):13.[doi:1001－3938（2010）0４－0013－05]
　WANG Xiang-yun.12Cr1MoVG steel welding joint hot cracking reason analysis and countermeasures[J].,2010,33(11):13.[doi:1001－3938（2010）0４－0013－05]
[10]李建一,田　鹏,孙志刚,等.螺旋埋弧焊管二步法焊接接头性能分析[J].焊管,2011,34(12):69.[doi:1001-3938（2011）12-0069-04]
　LI Jian-yi,TIAN Peng,SUN Zhi-gang,et al.Analysis on Welded Joint Performance of Two-step Welding SAWH Pipe[J].,2011,34(11):69.[doi:1001-3938（2011）12-0069-04]

备注/Memo

备注/Memo:

 

收稿日期: 2018-06-05
修改稿收稿日期: 2018-10-10

作者简介: 蔡洪能，男，教授，主要从事焊接结构与强度理论研究工作。

更新日期/Last Update: 2019-01-14