[1]黄杰,徐根涛.UOE焊管机组铣边机刀盘转速计算模型及铣削参数分析[J].焊管,2024,47(3):53-57.[doi:10.19291/j.cnki.1001-3938.2024.03.008]
　HUANG Jie,XU Gentao.Analysis of Calculation Model and Milling Parameter of the Cutter Head Speed of UOE Welding Unit Edge Milling Machine[J].,2024,47(3):53-57.[doi:10.19291/j.cnki.1001-3938.2024.03.008]
点击复制

UOE焊管机组铣边机刀盘转速计算模型及铣削参数分析()
分享到：

《焊管》[ISSN:1001-3938/CN:61-1160/TE]

卷:
47
期数:
2024年第3期
页码:
53-57
栏目:
应用与开发
出版日期:
2024-03-28

文章信息/Info

Title:
Analysis of Calculation Model and Milling Parameter of the Cutter Head Speed of UOE Welding Unit Edge Milling Machine
文章编号:
10.19291/j.cnki.1001-3938.2024.03.008
作者:
黄杰; 徐根涛
（宝山钢铁股份有限公司，上海 201900）
Author(s):
HUANG Jie;  XU Gentao
(Baoshan Iron & Steel Co., Ltd., Shanghai 201900, China)
关键词:
UOE焊管机组; 铣边机; 铣削线速度; 铣削厚度; 夹钳小车速度
Keywords:
UOE welding unit;  edge milling machine;  milling line speed;  milling thickness;  the speed of the clamp car
分类号:
TG506.9
DOI:
10.19291/j.cnki.1001-3938.2024.03.008
文献标志码:
B
摘要:
为了合理设置铣削参数、提高铣边机生产效率，推导了UOE大直径直缝埋弧焊管铣边机刀盘转速计算模型，并将模型计算结果与实际生产数据进行了对比验证。验证结果显示，计算得出的参数与生产时的实际参数基本一致。根据模型计算公式，利用Matlab计算软件分析了铣削厚度、铣削线速度对夹钳小车速度的影响，表明铣削厚度、铣削线速度与夹钳小车速度均为线性正相关。
Abstract:
In order to set the milling parameters reasonably and improve the production of the edge miller, a calculation model of the cutter head speed of the UOE large diameter straight welded pipe milling machine is published, and the calculation results of the model are compared with the actual production data. The verification results show that the calculated parameters are basically consistent with the actual parameters during production. According to the model calculation formula, the influence of milling thickness and milling line speed on the speed of the clamp car was analyzed using Matlab calculation software. The analysis showed that there was a linear positive correlation between milling thickness, milling line speed, and the speed of the clamp car.

相似文献/References:

[1]丁艳辉,李军,王继海.铣边机刀盘的精度检测[J].焊管,2009,32(6):57.[doi:1001－3938(2009)06－0057－02]
　DING Yan-hui,LI Jun,WANG Ji-hai.Precision Measurement of Miller Cutting Disc[J].,2009,32(3):57.[doi:1001－3938(2009)06－0057－02]
[2]刘洪飞.螺旋埋弧焊管机组铣边机刀片的使用寿命[J].焊管,2010,33(4):40.[doi:1001－3938（2010）0４－0040－05]
　LIU Hong-fei.Useful Life of Milling Machine Blade for Spiral Welded Pipe Unit[J].,2010,33(3):40.[doi:1001－3938（2010）0４－0040－05]
[3]罗红福,周秀峰,蔡小青.铣边机钢板精确对中方案及应用[J].焊管,2011,34(7):47.
[4]崔远洋,刘成坤.模块式铣边机刀盘的研制与应用[J].焊管,2011,34(10):33.[doi:1001-3938（2011）10-0033-04]
　LIU Chen-kun,CUI Yuan-yang.Development and Application of Module Type Milling Machine Cutting Disc[J].,2011,34(3):33.[doi:1001-3938（2011）10-0033-04]
[5]孙凤龙.UOE焊管生产线钢板微运动对钝边铣削影响分析[J].焊管,2013,36(10):42.[doi:１００１－３９３８（２０１3）10-0042-05]
　SUN Fenglong.Analysis on Milling Influence to Root Face of Steel Plate Micromotion in UOE Welded Pipe Production Line[J].,2013,36(3):42.[doi:１００１－３９３８（２０１3）10-0042-05]
[6]韩立坤,李 强,汪陇陇.Linsinger铣边机在螺旋预焊机组的应用研究[J].焊管,2014,37(9):51.[doi:１００１－３９３８（２０１4）09-0051-05]
　HAN Likun,LI Qiang,WANG Longlong.Application of Linsinger Edge Milling Machine in Spiral Pre-welding Unit[J].,2014,37(3):51.[doi:１００１－３９３８（２０１4）09-0051-05]
[7]陈 亮,胡宜新,刘 岩.高频焊林辛格铣边机改造探索[J].焊管,2015,38(2):51.[doi:１００１－３９３８（２０１5）02-0051-04]
　CHEN Liang,HU Yixin,LIU Yan.Modification Discussion of High Frequency Welding (HFW) Linsinger Edge Milling Machine[J].,2015,38(3):51.[doi:１００１－３９３８（２０１5）02-0051-04]
[8]冯 瑶,杨明秦,贾 熙,等.螺旋埋弧焊管生产线带钢坡口铣削尺寸稳定性分析[J].焊管,2020,43(12):33.[doi:10.19291/j.cnki.1001-3938.2020.12.007]
　FENG Yao,YANG Mingqin,JIA Xi,et al.Stability Analysis of Strip Steel Groove Milling Size of SSAW Pipe Production Line[J].,2020,43(3):33.[doi:10.19291/j.cnki.1001-3938.2020.12.007]
[9]韩立坤.焊管生产线铣边机关键功能的自动控制设计[J].焊管,2022,45(7):42.[doi:10.19291/j.cnki.1001-3938.2022.07.008]
　HAN Likun.Automatic Control Design of Key Functions of Edge Milling Machine in Welded Pipe Production Line[J].,2022,45(3):42.[doi:10.19291/j.cnki.1001-3938.2022.07.008]

备注/Memo

备注/Memo:
收稿日期：2023-03-13作者简介：黄杰（1986—），男，工学硕士，工程师，主要从事钢管设备维护及项目管理工作。
更新日期/Last Update: 2024-03-28